Skip to content
Open 24/7 for emergenciesCall 24/7 · 07861 933265
Call 07861 933265WhatsApp us

Washing Machine Leaking From the Bottom? Find the Source

By Emergency Plumb,

A puddle in front of the washing machine looks like the machine has failed, but more often than not the water is coming from the plumbing around it: a hose, a valve or the waste pipe it empties into. Those are quick plumbing fixes. Working out which one it is takes about ten minutes and a torch.

Short answer: Switch the machine off, close its water valve and pull it out. Leaks while it fills point to the supply hose or valve. Leaks while it drains point to the waste hose, the trap or the standpipe. Water from under the drum during a wash usually means a fault inside the machine.

First, make it safe

  1. Switch the machine off at the wall, but only if the socket and the floor in front of it are dry. If they are wet, turn it off at the consumer unit instead.
  2. Close the valve on the cold supply. It is usually a small lever or a slotted screw on the pipe behind the machine or under the sink, a quarter turn so it sits across the pipe.
  3. Mop up and put a towel down, so that you can see fresh water when it appears.

If the valve won’t close, or water is still running from the pipe after it has, turn the main stopcock clockwise until it stops and treat it as a water leak.

Watch when it leaks

Ease the machine out far enough to see the hoses, then run a short rinse cycle with the floor dry and watch.

While it fills. Water at the back while the drum fills is on the supply side. Check where the grey or blue inlet hose screws onto the valve: a worn rubber washer inside the nut is the most common cause, and the nut can work loose when the machine is moved or walks during a spin. A hose that is cracked or bulging near its ends needs replacing, not taping.

While it drains. If the water only appears as the pump empties the drum, follow the grey corrugated waste hose. It either hooks into a standpipe behind the machine or connects to a spigot on the sink trap. Look for a split in the hose, a loose clip at the sink, or water backing up out of the standpipe. A standpipe that overflows is usually partly blocked with lint and soap.

During the wash, from underneath. A steady drip from under the front, with dry hoses, points inside the machine: the door seal, the pump, the drum or the internal hoses. That is a job for an appliance engineer or the manufacturer, not a plumber, and you can leave the valve shut until it is seen.

Even when it is switched off. Water that keeps coming with the machine off is from the plumbing: the valve itself is weeping, or a pipe nearby is leaking and running along the floor to the lowest point, which is often under the machine. Our guide to finding a hidden water leak explains how to check the water meter.

The checks that find most leaks

  • Unscrew the inlet hose, look at the washer inside the nut, and replace it if it is flat, cracked or missing. Screw it back hand-tight plus a little, no more.
  • Pull the waste hose out of the standpipe and check it goes in only a short way. Pushed in too deep, it can siphon water out of the machine and over the top.
  • Run the kitchen tap hard for a minute. If the sink drains slowly too, the shared trap or waste pipe is blocked; see how to unblock a sink.
  • Look at the floor under the machine for staining or soft boards. In a flat, a slow leak here can show up first as a stain on the ceiling below.

When to call us

A plumbing leak around a washing machine is usually a short visit: a new washer or hose, a valve that shuts properly, or a waste pipe cleared and refitted at the right height. If the machine is also moving to a new spot, or it was never plumbed in properly, our washing machine installation service puts in a new valve and waste.

Water coming through a ceiling below, or a valve that won’t close at all, is a different matter: turn the stopcock off and ring an emergency plumber, day or night.

Questions people ask

Is it safe to use the washing machine while it is leaking?

No. Water and a mains socket behind the machine are a bad mix. Switch it off at the wall if the socket and floor are dry, otherwise at the consumer unit, and close the valve on its water supply before you pull it out.

Can a plumber fix a washing machine?

A plumber fixes the water side, which is where many leaks start, the supply hoses, valves, the waste hose and the trap or standpipe it drains into. A fault inside the drum, pump or door seal is a job for an appliance engineer or the manufacturer. We will tell you which it is once we have looked, and we only charge for the time.

Why does it only leak when it drains?

Then the water is going wrong on its way out, a split or loose waste hose, a blocked sink trap or standpipe that cannot take the flow, or a waste hose pushed too far down the standpipe. Run the sink tap hard for a minute; if the sink drains slowly too, the blockage is in the pipe, not the machine.

What does it cost to sort out?

There is no call-out charge. It is £110 for the first hour and £45 for each extra half hour, plus any parts, such as a new hose or valve. Most supply and waste leaks are fixed well inside the first hour.

Call 07861 933265WhatsApp