Saniflo Keeps Running or Starting on Its Own? Causes
By Emergency Plumb,
A macerator should run for a few seconds after a flush and then stop. One that keeps going, or that wakes the house at 3am with a short burst when nobody has used it, is telling you something specific. Most of the causes are cheap to fix if they are caught before the motor wears out.
Short answer: First rule out water trickling in from a dripping tap or a cistern that never stops filling. If nothing is feeding it, the usual suspects are a worn non-return valve letting pumped water fall back, or a pressure switch that is scaled up, dirty or damaged by bleach.
Start with what feeds it
A macerator switches on when water in its chamber reaches a certain level. It does not know whether that water came from a flush or from a slow drip.
- The toilet cistern. Lift the lid and listen. If water is still trickling into the pan long after a flush, the fill valve or flush valve is letting by. Our guide to a toilet running into the pan covers the fix.
- A basin, shower or bath on the same unit. A dripping tap or a shower valve that does not fully close sends a steady trickle into the chamber.
- A washing machine or dishwasher, if one is connected, can do the same through a valve that weeps.
Turn off the isolation valves on these one at a time. If the unit goes quiet, you have found the cause, and it is a plumbing fix, not a macerator repair.
If nothing is feeding it
Short bursts at random times. This is the classic sign of a worn non-return valve, the flap that stops pumped waste falling back down the discharge pipe. When it fails, water runs back, the chamber refills and the pump starts again. It is a small part and usually a straightforward swap.
It runs on and on after a flush. The pressure switch, and the membrane over it, tell the unit when it is empty. Scale, dirt or a damaged membrane can leave it stuck “on”. Saniflo warns that bleach and ordinary toilet cleaners can damage that membrane and make the switch over-sensitive. A blocked air vent can upset the switch in the same way.
It runs, but the water goes down slowly. That points to a part-blocked pipe or chamber rather than a switch, see our guide to a blocked Saniflo.
What you can do now
- Switch the unit off at the spur between uses, so the motor is not running for hours.
- Fix any dripping tap or running cistern that drains into it.
- If it has not been descaled for a year or more, descale it with a product made for macerators.
- Don’t open the casing yourself. The manufacturer says to disconnect the power before any check and to leave dismantling to a repair engineer.
Getting it repaired
If it still runs on, our emergency Saniflo repair service comes out across London, day or night. A non-return valve, membrane or switch is usually replaced in the same visit if we carry the part for your model. You pay £110 for the first hour, £45 per half hour after that, plus parts, and nothing for the call-out.
Questions people ask
Is it dangerous if my Saniflo keeps running?
It isn't dangerous to you, but it is hard on the motor. A pump that runs for long periods can overheat and cut out, and over time it wears the motor out. Switch it off at the spur between uses until it is fixed.
Why does it start by itself in the middle of the night?
Usually because a little water is reaching it when nobody is using it, a dripping basin tap or a cistern that never quite stops filling, or because water it has already pumped out is falling back through a worn non-return valve.
Will descaling fix it?
Sometimes. Scale and dirt on the pressure switch membrane can make the unit think it is still full. Descaling with a product made for macerators is worth trying first if the unit has not been descaled for a long time.
My Saniflo started running on after I used bleach. Why?
Saniflo warns that household bleach can damage the rubber membrane over the pressure switch, which can make the switch over-sensitive and the unit run too long. That usually needs the membrane or switch replaced.
Sources
- How do you maintain a Saniflo Pump?, SFA Saniflo
- Saniplus installation and user manual, fault finding, ManualsLib