Skip to content
Open 24/7 for emergenciesCall 24/7 · 07861 933265
Call 07861 933265WhatsApp us

No Hot Water From the Bath Unless a Cold Tap Is Running?

By Emergency Plumb,

You run the bath, hand under the tap, waiting. Lukewarm. Then someone pops into the kitchen, fills the kettle from the cold tap, and suddenly your bath tap is properly hot. They turn it off and you’re back to tepid. It feels like the house is having a laugh at you, but there’s a real and quite logical reason, and it’s rarely the boiler or the cylinder.

Short answer: If hot water only reaches the bath while a cold tap is running, cold mains water is almost always getting into your hot pipe through a faulty mixer tap or shower valve somewhere in the house. The cold side has more pressure, so it pushes into the hot pipe. Opening a cold tap drops that pressure and lets the real hot through. Find the mixer that’s passing by isolating each one in turn, then replace its check valves or cartridge.

Why does turning on a cold tap bring the hot water back?

Most homes have hot and cold water at different pressures. The cold usually comes straight off the mains, while the hot has to push through a cylinder, a combi’s heat exchanger or a loft-fed system, so it arrives with less force. Every mixer tap and mixer shower brings those two supplies together in one body.

Inside each mixer, small one-way valves are meant to keep the supplies from flowing backwards into each other. Heat Geek’s guide to mixing valve faults says these non-return valves often fail, or were never fitted in the first place. Once that happens, the stronger cold side can overpower the hot and push cold water back up the hot pipe whenever a hot tap is opened somewhere.

So when you open the bath’s hot tap, you’re partly drawing cold water that has been forced into the hot pipework. When someone runs a cold tap elsewhere, the cold pressure sags for a moment, the hot side is no longer outgunned, and proper hot water comes through. Heat Geek notes that the effect can be anything from a degree or two cooler than normal to almost completely cold, and that it can come and go, which is why it drives people mad.

Illustration: a chrome single-lever basin mixer running into a white basin in a grey-tiled bathroom, with a little steam in the air

Illustration made with AI to show a mixer tap running. It is not a photo of one of our jobs.

Is it the bath tap, or a mixer somewhere else?

Here’s how to narrow it down. Nothing here needs you to take anything apart.

  1. Note exactly when it happens. Is it only the bath, or do the basin and kitchen hot taps go lukewarm too? If every hot tap is affected, the culprit could be any mixer in the house.
  2. Find the isolation valves. Most mixers have a small valve on the hot and cold pipes underneath, often a slot you turn with a flat screwdriver. Showers often have them behind an access panel or built into the valve.
  3. Shut off one mixer at a time. Close the cold valve under one mixer, then run the bath hot tap on its own. If it comes through hot, you’ve found your leaky mixer.
  4. Don’t forget the showers. A thermostatic or manual mixer shower is a common source, especially an older one with worn internals.
  5. Write it down. Note which valve you turned and which way, so you can put everything back as it was.

If you’ve got the reverse problem, where your cold taps run warm, that’s the same fault working the other way round. Our guide on why your cold water is warm explains that version.

What it usually is

What you noticeUsual cause
Bath hot is lukewarm until any cold tap is openedCold crossing into the hot pipe at a mixer
Fixed by isolating one particular mixerFailed check valves or worn cartridge in that mixer
Only one thermostatic shower or bath filler misbehavesBlocked filters or a sticking thermostatic cartridge
Hot weak everywhere, cold strong, all the timeNormal for some systems, see low hot water pressure
Combi hot dribbles and never heats, with or without a cold tapFlow under the boiler’s minimum, see below

Could it be the combi or the cylinder after all?

Sometimes. If you’ve got a combi, opening a cold tap should make things worse, not better, because it takes flow away from the boiler. Our guide to a combi cutting out when another tap is turned on covers that one. So if a cold tap reliably improves your bath, it still points to cross-flow rather than the boiler.

With a hot water cylinder, Heat Geek suggests a neat test: shut off the cold feed to the cylinder, then run a hot tap. If water keeps flowing, it has to be coming from the cold supply through a mixer, because the cylinder can’t push anything without its feed.

How we sort it out

We find the mixer that’s passing, then fix it in the simplest way that will last:

  • New check valves or cartridge. Many good-quality mixers and shower valves have replaceable parts. We swap them, clean the filters and test both sides.
  • A check valve on the pipe. Heat Geek points out that fitting a non-return valve on the hot pipe just below the faulty fitting is a common fix, and often cheaper than a new mixer.
  • A new tap. If the mixer is old, badly scaled or parts aren’t made any more, tap replacement is usually the cleaner answer.

If you’d like someone to go through all the bathroom fittings in one visit, our bathroom repairs and fault finding service does exactly that.

Pricing is simple: no call-out charge, £110 for the first hour, then £45 for each half hour, plus parts. You’ll find the full breakdown on our prices page.

Lost hot water completely?

If the hot has gone altogether and it’s freezing, our 24-hour emergency plumbers cover London and the M25 towns and usually reach you in 60 minutes. See everything else we do on our emergency plumber in London page, or just call or WhatsApp 07861 933265 and tell us which taps are playing up.

Questions people ask

Why do I only get hot water when a cold tap is running somewhere else?

Usually because a mixer tap or shower valve somewhere in the house is letting mains cold water push into the hot pipe. The cold side has more pressure, so it wins and fills your hot pipe with cold. When someone opens a cold tap, the cold pressure dips, the real hot water can finally get through, and the bath warms up.

Which tap or shower is causing it?

Often not the one you're using. Any mixer that has both hot and cold going into it can be the leak point, including kitchen mixers, bath fillers, basin monoblocs and shower valves. The usual way to find it is to shut off the supplies to each mixer in turn until the problem stops.

Can a thermostatic shower or bath valve stop hot water coming through?

Yes. Thermostatic valves are designed to cut the hot right back if the cold supply to them drops, so nobody gets scalded. If the cold filter or check valve inside one is choked, it can behave oddly and restrict the hot. Cleaning or replacing the cartridge and its filters usually sorts it.

I've got a combi. Could it be the boiler?

Opening a cold tap shouldn't help a combi heat water; if anything it takes flow away. So if your bath only gets hot with a cold tap open, cross-flow at a mixer is still the first suspect. If the hot just trickles and never warms up at all, the flow may be too low for the combi to fire, which is a different fault.

What does it cost to sort out?

No call-out fee. We charge £110 for the first hour and £45 for each half hour after that, plus parts, at any time of day or night.

Sources

  1. Mixing Valve Faults and Issues: How to Diagnose Them, Heat Geek
Call 07861 933265WhatsApp