Skip to content
Open 24/7 for emergenciesCall 24/7 · 07861 933265
Call 07861 933265WhatsApp us

How to Turn Off the Water to a Toilet (Isolation Valve)

By Emergency Plumb,

A toilet that will not stop filling, a cistern leaking onto the floor, or a pan about to overflow: the first job is always to stop the water going in. Nearly every modern toilet has its own small valve for exactly this, and closing it takes a few seconds.

Short answer: Find the small valve on the pipe running into the cistern. Turn the slot a quarter turn with a coin or a flat screwdriver so it sits across the pipe. The cistern stops filling. If there is no valve, or it will not close, turn off the main stopcock.

Step 1: find the valve

Follow the pipe that runs into the cistern, usually at its base on one side. Somewhere along it, often just under the cistern or where the pipe comes out of the wall, is a short chrome or brass fitting with a slot or a small lever on it. That is the isolation valve, sometimes called an isolating valve or service valve.

On a concealed cistern hidden behind boxing, look for a removable panel. On many wall-hung toilets the valve is reached by lifting off the flush plate.

Step 2: turn it a quarter turn

  • Slotted valve: put a coin, a flat screwdriver or a butter knife in the slot and turn it a quarter turn so the slot runs across the pipe.
  • Lever valve: turn the little handle so it points across the pipe.

Never force it. Old valves can be stiff with scale, and a valve twisted too hard can start to leak from its own body.

Step 3: check it worked

Flush once. If the cistern stays empty, the water is off. If it slowly refills, the valve is no longer sealing; go to the main stopcock instead.

No valve, or it won’t close?

Turn off the main stopcock. In most houses it is under the kitchen sink. In flats it can be in the kitchen, a hall cupboard or the bathroom. Our guide where is my stopcock? goes through the usual places in London homes. If the stopcock itself is stuck, see seized stopcock.

If the toilet is fed from a tank in the loft, closing the mains will not empty the tank. Look for a valve on the pipe leaving the tank, or tie the tank’s float arm up so it stops filling.

Once the water is off

  • Overflowing pan: do not flush again. See overflowing or blocked toilet.
  • Running or leaking cistern: the toilet repair page explains what usually fails.
  • Water on the floor: mop up, and if you are upstairs or in a flat, check the ceiling below.

Worth fitting if you don’t have one

A toilet with no isolation valve means turning off the whole home’s water for a five-minute repair. We fit one as part of any toilet repair when it is missing. Call 07861 933265: no call-out charge, £110 for the first hour and £45 for each half hour after, plus parts.

Questions people ask

Where is the isolation valve on a toilet?

On the pipe that feeds the cistern, usually a few centimetres below it or near where the pipe leaves the wall or floor. On a concealed cistern it sits behind the access panel, or behind the flush plate on many wall-hung toilets.

Which way do I turn the slot to turn the water off?

Turn the slot so it sits across the pipe, at right angles to it. In line with the pipe means open; across the pipe means closed. It only needs a quarter turn.

What if my toilet has no isolation valve?

Turn off the main stopcock instead. That stops the water to the whole home. If the cistern is fed from a cold water tank in the loft, there may be a gate valve on the pipe leaving the tank that controls the bathroom.

The valve is turned off but the cistern still fills. Why?

The valve is worn and no longer seals, which is common on old ones that have never been turned. Use the main stopcock and have the valve replaced at the same time as the repair.

Can I turn the isolation valve back on straight away?

Once the repair is done, yes. Open it slowly and watch the joints for drips as the cistern fills. If the cistern overflows, close it again and call a plumber.

Call 07861 933265WhatsApp