Gas Safe registered · No. 932798 ★★★★★ 9.8 Checkatrade · 145 reviews ★★★★★ 4.9 Google · 312 reviews Company No. 12326959 24/7 · including bank holidays
Planned work · London · from £2,400 per floor

Underfloor Heating Installation in London

Wet underfloor heating runs at 35–45°C rather than the 70°C a radiator needs.

Underfloor heating installation in London
No call-out feeNo night or weekend surchargeFixed price before we start12-month workmanship guarantee

which is why it pairs so well with a modern condensing boiler and why it is close to mandatory if a heat pump is anywhere in your plans. It also gives you back every wall a radiator was using.

What you get

Underfloor heating installation in London: what the price includes

  • 01
    Screed, low-profile or between joists

    A new extension takes pipe in screed and performs best. A retrofit onto an existing floor takes a low-profile overlay of 15–20 mm, which affects door heights and thresholds. A suspended timber floor takes spreader plates between the joists. We survey before specifying, because the floor decides the system.

  • 02
    Heat loss calculated room by room

    Underfloor output is limited by floor surface temperature, you cannot simply turn it up. If a room's heat loss exceeds what the floor can deliver, insulation or a supplementary emitter is part of the answer, and it is far cheaper to know that now than after the screed is down.

  • 03
    Manifold, blending and zoning

    A blending valve drops flow temperature from the boiler circuit to the loop temperature, and the manifold balances each loop so no room runs cold. Zoned actuators and per-room stats are the difference between comfortable and expensive to run.

  • 04
    Pressure-tested before anything covers it

    Loops go in continuous, with no joints under the floor, and are pressurised and held before screeding or boarding. A leak found at that stage costs an hour. Found later it costs a floor.

  • 05
    Floor finish matters

    Tile and stone are ideal, engineered timber works within a temperature limit, and thick carpet or heavy underlay can insulate the system into uselessness. We will tell you the tog ceiling for your build-up before you order the flooring, not after.

What this means in London

Local conditions we work around

Hard water is the defining fact for London heating. At 280 to 320 ppm, scale builds on the hottest surface in the system, which is the boiler heat exchanger, and every millimetre of it costs efficiency and shortens the life of the unit. It is why we flush before commissioning a new boiler, why we fit a scale reducer on the mains where the system warrants it, and why an unvented cylinder in London needs its annual service rather more than the manual implies.

Where we do this in London

Covered across London

Same published rate card and the same twelve-month workmanship guarantee everywhere below, there is no postcode loading. Each area has its own page with an arrival time taken from our job records rather than chosen for a website.

Straight answers

Underfloor heating installation in London, your questions

Can I retrofit underfloor heating without lifting the floor?
Yes, with a low-profile overlay system of 15 to 20 mm plus the finish. It raises the floor and needs doors trimmed and thresholds reworked, but it avoids excavation. On a suspended timber floor the alternative is spreader plates from below, which avoids raising anything.
Is underfloor heating expensive to run?
Wet underfloor is generally cheaper to run than radiators for the same comfort, because the lower flow temperature keeps a condensing boiler in condensing mode. Electric mat systems are the opposite and are best kept to a single bathroom.
How long does it take to warm up?
A screed floor has real thermal mass, so it takes hours rather than minutes and is designed to run steadily rather than be switched on and off. Overlay systems respond much faster. Which one you have should shape how you set the controls.
Does it work with a heat pump?
It is the ideal pairing. A heat pump is most efficient at low flow temperatures, and underfloor is a low-temperature emitter. If a heat pump is anywhere in your ten-year plan, underfloor now makes that conversion straightforward later.
Can I have it in one room only?
Yes, bathrooms and kitchens are the common single-room jobs. It runs as its own zone off the existing system with its own blending valve and stat.
How does London hard water affect heating work?
Considerably. Scale builds on the hottest surface in the system, which is the boiler heat exchanger, and every millimetre costs efficiency and life. It is why we flush before commissioning a new boiler here, why kettling is the most common noise complaint we get in London, and why an unvented cylinder in this city genuinely needs its annual service rather than nominally needing it.
24 hours · 365 days · London

Water where it
shouldn't be? Call.

A person answers, not a menu. You'll have an arrival time and a price range before you hang up.

020 3674 8514

Or WhatsApp 07865 292684, photos help us bring the right parts

Our engineers